Vtech VM333-2

Vtech VM333-2 manual

(1)
  • User’s manual
    VM333/VM333-2/VM303
    Safe & Sound
    TM
    Pan & Tilt Full Color
    Video monitor
    Congratulations
    on purchasing your new VTech product. Before
    using this product, please read Important
    safety instructions below.
    For support, shopping, and everything new at
    VTech, visit our website at
    www.vtechphones.com.
    Register online to get an additional
    3-month warranty!
    Visit www.vtechphones.com.
    Registration
    Register your product online for
    enhanced warranty support.
    Product news
    Learn about the latest VTech
    products.
    You can power up the parent unit by connecting
    it to AC power or to the rechargeable battery
    provided. Even if the parent unit is connected to
    AC power, we recommend you also install the
    battery. This guarantees continual operation in
    case of a power outage.
    Install the battery as shown below.
    With the label THIS SIDE UP facing up,
    insert the small tabs of the battery into
    the slots inside the battery compartment.
    Make sure the metallic contact is correctly
    oriented as shown below. Push the battery
    into the battery compartment until it clicks
    securely into place.
    Align the battery compartment cover flat
    against the battery compartment, then slide
    it towards the center of the parent unit until it
    clicks into place.
    Replace the battery
    To replace the battery, press down on the large
    tab of the battery and pull it out of the battery
    compartment, then follow the steps above to
    install the battery.
    1.
    2.
    The operating time for using the
    rechargeable battery is short. If you want
    to monitor your baby for a long time, we
    recommend you connect the parent unit to
    AC power.
    If the parent unit will not be used for a long
    time, disconnect and remove the battery to
    prevent possible leakage.
    Use only the battery supplied with this
    product.
    Use only the parent unit power adapter or
    the baby unit power adapter supplied with
    this product.
    The parent unit power adapter and baby
    unit power adapter are intended to be
    correctly oriented in a vertical or floor mount
    position. The prongs are not designed to
    hold the plug in place if it is plugged into a
    ceiling, under-the-table or cabinet outlet.
    Make sure the parent unit, the baby unit
    and the power adapter cord are out of reach
    of children.
    Connect the baby unit
    Connect the parent unit
    Charge the parent unit battery
    Once you have installed the parent unit and
    its battery, press and hold to turn it on. The
    battery icon indicates the battery status (see
    the table below). The parent unit battery is fully
    charged after 12 hours of continuous charging.
    The standby time varies depending on the
    sensitivity level you set, your actual use and the
    age of the battery.
    When the parent unit is operating in battery
    mode and the battery is low, you need to charge
    the parent unit without interruption for at least
    30 minutes to give the parent unit enough
    charge to use for a short time. When operating
    in low battery condition, the parent unit displays
    Battery low and . The parent unit plays short
    beeps to alert you.
    The following table summarizes the battery
    charge indicators and actions to take.
    Battery
    indicators
    Battery
    status
    Action
    The battery
    icon is off
    and
    displays.
    No battery
    is installed
    but operates
    using AC
    power, or the
    battery has
    been installed
    incorrectly.
    Install the
    parent unit
    battery.
    Charge
    without
    interruption
    (at least 30
    minutes).
    The screen
    displays
    Battery low
    and . The
    light
    flashes.
    The battery
    has very little
    charge and
    may be used
    for only a
    short time.
    Charge
    without
    interruption
    (about 30
    minutes).
    The battery
    icon
    becomes
    solid .
    The battery is
    fully charged.
    To keep
    the battery
    charged,
    connect it to
    AC power
    when not in
    use.
    When you charge the battery initially or it is
    not used for a long period of time, charge it
    for 12 hours continuously. It takes longer to
    charge the battery when the parent unit is
    turned on. To shorten the charging time, turn
    the parent unit off while charging.
    You may test the baby monitor before initial use,
    and at regular times thereafter.
    To test your baby monitor:
    Place the parent unit and the baby unit in the
    same room to test the product.
    Press and hold on the parent unit the
    screen displays Please Wait....
    Slide ON/OFF on the baby unit to turn it on.
    If the parent unit displays an image from the
    baby unit. Your baby monitor is now ready
    for use.
    Make sure the baby unit is at least 3 feet
    away from the parent unit.
    If both units are not connected, the parent
    unit displays No Link for a few seconds.
    Then it displays Please Wait... and
    flashes.
    1.
    2.
    3.
    4.
    Positioning the baby monitor
    Place the parent unit within the operating range
    of the baby unit. We recommend the parent
    unit is at least 3 feet away from the baby unit
    to avoid audio feedback. If you still experience
    audio feedback, move the parent unit and the
    baby unit farther apart.
    For better image quality, do not place the
    baby unit too far away from your baby.
    Operating range
    The operating range of the baby monitor is up
    to 1,000 feet outdoors or 150 feet indoors. The
    actual operating range may vary depending on the
    environmental conditions and other interferences
    such as walls, doors and other obstructions.
    Baby unit overview
    Parent unit overview
    Parent unit lights
    LINK
    On when strong signal strength is
    detected between the parent unit and
    the selected baby unit.
    Flashes when the parent unit cannot
    link to the selected baby unit.
    Off when the parent unit is turned off.
    On when the parent unit battery is
    being charged.
    Flashes when the parent unit battery
    is low and needs charging.
    Off when the parent unit battery is
    fully charged, or when no battery is
    installed.
    TALK
    On when the parent unit is talking to
    the baby unit.
    On when the speaker volume of the
    parent unit is turned off.
    Parent unit display icons
    Connection status
    - displays when strong signal
    strength is detected between the
    baby unit and the parent unit.
    - or displays when moderate signal
    strength is detected between the
    baby unit and the parent unit.
    - displays when the link between the
    baby unit and the parent unit
    is lost.
    or or
    or
    Current view status
    - Displays the number of the baby unit
    that is being viewed when in Single
    Baby unit.
    - Displays the highlighted baby unit
    when in Patrol Mode.
    Zoom
    - Displays when the camera at the
    baby unit has zoomed in.
    Temperature alert
    - Displays when the temperature alert
    is set to on.
    57
    o
    F Real-time temperature
    - Displays the real-time temperature of
    the selected baby unit.
    or
    or
    Sound level indicators
    -
    Displays the sound level according to
    the scales of loudness when there is
    sound transmitted from the baby unit.
    Speaker volume
    - Displays the speaker volume of the
    parent unit is turned off.
    Speaker volume
    - Displays the speaker volume level
    while adjusting.
    Battery status
    -
    animates when the battery is charging.
    - displays solid when the battery is
    fully charged.
    - displays when the battery is low
    and needs charging.
    - displays when no battery is
    installed but operates using AC
    power, or the battery has been
    installed incorrectly.
    Parent unit main menu icons
    Monitoring mode
    You can choose to monitor in Single
    Baby unit, Split Baby unit or Patrol
    Mode if there are more than one
    baby units in your system.
    Language
    You can select a language (English,
    French or Spanish) to be used in all
    screen displays.
    Display
    - You can change the brightness of the
    parent unit screen.
    - You can change the contrast of the
    parent unit screen.
    Alert tone
    - You can set whether the parent
    unit beeps whenever the parent unit
    operates in low battery condition.
    - You can set whether the parent unit
    beeps whenever the link between the
    parent unit and the baby unit is lost.
    - You may turn on the sound alert so
    that the parent unit beeps as soon
    as the baby unit detects sounds
    which light up four sound level
    indicators on the parent unit when
    the parent unit volume is turned off
    manually.
    Temperature
    - You can set the desired minimum
    room temperature of the baby unit.
    - You can set the desired maximum
    room temperature of the baby unit.
    - You can set whether the parent unit
    beeps whenever the temperature is out
    of the preset temperature range.
    -You can set the temperature scale of
    the baby unit.
    Sensitivity
    - You can use the parent unit to
    change the sound sensitivity level
    of the baby units.
    Install the battery
    Connect and charge the
    battery
    Metallic
    contact
    Step 1
    Step 2
    Step 1
    Step 2
    Step 1
    Step 2
    PAIR
    Threaded socket
    Sound activation
    - You can set the screen to be turned
    on automatically whenever there
    are sounds detected from the baby
    units when the parent unit screen is
    turned off manually.
    Vibration
    - You may turn on the vibration alert
    so that the parent unit vibrates as
    soon as the baby unit detects sounds
    which light up three sound level
    indicators on the parent unit.
    Pair/unpair
    - The baby units and parent unit
    provided are already paired. You can
    add or replace baby units (VM303,
    purchased separately) to your baby
    monitor system.
    Parent unit display messages
    Battery low
    When the parent unit
    is powered by the
    rechargeable battery
    and the battery level
    is low, it needs to be
    recharged.
    Failed to connect
    The parent unit fails to
    switch to the next baby
    unit in Single Baby
    unit or Patrol Mode.
    No Link
    The selected baby unit
    slot is not linked to the
    parent unit.
    Pairing failed
    The selected baby unit
    cannot be paired with
    the parent unit.
    Conrm to unpair?
    You try to unpair the
    baby unit(s). The
    operation needs your
    confirmation.
    Pairing completed
    The selected baby unit
    has been paired with
    the parent unit.
    Unpairing completed
    The selected baby
    unit(s) has been
    unpaired with the
    parent unit.
    Please Wait...
    The link between the
    parent unit and the
    selected baby unit is
    lost, or the selected
    baby unit is out of
    range, or the selected
    baby unit slot is empty.
    When you have only
    one paired baby unit
    and the link is lost,
    or you have multiple
    paired baby units and
    the links are lost.
    Temperature too low
    The temperature
    detected from the
    selected baby unit is
    below the set minimum
    temperature.
    Temperature too high
    The temperature
    detected from the
    selected baby unit
    is above the set
    maximum temperature.
    Power on or off the baby unit
    Slide ON/OFF to the left to turn on the baby
    unit. The ON/OFF LED light turns on.
    Slide ON/OFF to the right to turn off the baby
    unit. The ON/OFF LED light turns off.
    Power on or off the parent unit
    Press and hold to turn on the parent unit.
    The LINK light turns on.
    Press and hold again to turn off the
    parent unit. The LINK light turns off.
    The LINK light flashes when the parent
    unit cannot link to the selected baby
    unit.
    Turn on or off the parent unit
    screen
    You can turn on or off the parent unit screen
    without powering off the parent unit. You can still
    hear sound from the baby unit.
    Press on the parent unit at any time.
    Adjust speaker volume for parent
    unit
    You can change the speaker volume from
    Volume 1 to Volume 5, or turn it off.
    When the speaker volume is set to off,
    appears briefly and the light turns on.
    To adjust the speaker volume:
    Press VOL when the parent unit is not
    in use.
    Press , , or to adjust the speaker
    volume.
    Adjust speaker volume for baby
    unit
    You can change the speaker volume.
    To adjust the speaker volume:
    Press
    +
    or
    -
    on the baby unit at any time.
    Adjust display
    LCD brightness
    You can change the brightness of the parent unit
    screen from Level 1 to Level 5.
    To set the brightness of the parent unit screen:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose DISPLAY, then press
    MENU/SELECT to select.
    Press or to choose Brightness.
    Press or to choose the desired level of
    brightness, then press MENU/SELECT to
    confirm your selection.
    LCD contrast
    You can change the contrast of the parent unit
    screen from Level 1 to Level 5.
    To set the contrast of the parent unit screen:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose DISPLAY, then press
    MENU/SELECT to select.
    Press or to choose Contrast.
    Press or to choose the desired level
    of contrast, then press MENU/SELECT to
    confirm your selection.
    1.
    2.
    1.
    2.
    3.
    4.
    1.
    2.
    3.
    4.
    Set the language
    You can select a language (English, French or
    Spanish) to be used in all screen displays.
    To change the language:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose LANGUAGE
    (Langue if French is set, or Idioma if
    Spanish is set).
    Press or to choose English, Français
    or Español.
    Monitoring mode
    You can choose to monitor in Single Baby
    unit, Split Baby unit or Patrol Mode if there
    are more than one baby units in your system.
    To change the monitoring mode:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose MONITORING
    MODE, then press MENU/SELECT to select.
    Press or to choose Single Baby unit,
    Split Baby unit or Patrol Mode.
    Single Baby unit - Press or to
    choose a desired baby unit. The parent
    unit only displays image of one baby unit.
    You may change to view images from
    different baby units by pressing in this
    mode.
    Split Baby unit - The parent unit displays
    multiple baby unit images in a maximum of
    four in one screen. If there are more than
    four baby units in your system, images
    will be shown on two split screens, which
    alternates with each other automatically.
    Patrol Mode - The parent unit patrols to
    display images from different baby units
    in every 7 seconds. You may change to
    view images from different baby units even
    though the scanning period is not expired
    by pressing in this mode.
    Press MENU/SELECT to confirm your
    selection.
    Monitoring mode is not applicable when
    there is only one baby unit.
    1.
    2.
    3.
    1.
    2.
    3.
    4.
    View
    You can change the screen to view images from
    different baby units.
    To view different baby units while in Single
    Baby unit:
    Press repeatedly to switch to the desired
    baby unit. The switching is in chronological
    order: Baby unit 1 to Baby unit 4.
    To view different baby units while in Split
    Baby unit:
    Press repeatedly to enlarge and switch
    to the desired baby unit. The switching is in
    chronological order: Baby unit 1 to Baby unit
    4. The Split Baby unit mode resumes after
    a while.
    To view different baby units while in Patrol
    mode:
    Press repeatedly to switch to the desired
    baby unit even if the scanning period on
    a particular baby unit is not expired. The
    switching is in chronological order: Baby unit 1
    to Baby unit 4.
    If the switching fails, the screen displays
    Failed to connect. Try the switching
    again.
    Zoom
    You can zoom in or out while viewing image
    from baby unit in Single Baby unit and
    Patrol mode.
    To zoom in or out:
    Press to zoom in. Press , , or to move
    the zoomed image upward, downward, leftward
    or rightward correspondingly. Press again to
    zoom out.
    In Split Baby unit, is not available.
    Talk to the baby unit
    You can broadcast messages from the parent
    unit to any one of the baby units.
    To talk to the baby unit:
    Press and hold TALK when the parent unit is
    in Single Baby unit or viewing particular baby
    unit in Patrol Mode. Speak towards the MIC
    (microphone) on the parent unit. The TALK light
    is on when the voice connection to the baby unit
    is made. Your voice is broadcast to the baby
    unit. Release the key to stop the broadcast.
    The TALK feature does not work in Split
    Baby unit.
    Night vision
    To help you monitor your baby even at night,
    the baby unit automatically uses the light from
    its infrared LEDs for transmitting images to the
    parent unit when it is turned on in a dark room.
    However, it only transmits black-and-white
    images.
    Set the alert tone
    Low battery tone alert
    You can set whether the parent unit beeps
    whenever the parent unit operates in low battery
    condition.
    To set the low battery tone alert:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose ALERT TONE, then
    press MENU/SELECT to select.
    Press or choose Low Battery Tone.
    Press or to choose On or Off, then press
    MENU/SELECT to confirm your selection.
    1.
    2.
    3.
    4.
    No link alert
    You can set whether the parent unit beeps
    whenever the link between the parent unit and
    the baby unit is lost.
    To set the no link alert of the parent unit:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose ALERT TONE, then
    press MENU/SELECT to select.
    Press or to choose No Link Alert.
    Press or to choose On or Off, then press
    MENU/SELECT to confirm your selection.
    Sound Alert
    When the parent unit volume is turned off
    manually, you may turn on the sound alert so
    that the parent unit beeps as soon as the baby
    unit detects sounds which light up four sound
    level indicators on the parent unit.
    To set the sound alert of the baby unit:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose ALERT TONE, then
    press MENU/SELECT to select.
    Press or to choose Sound Alert.
    Press or to choose On or Off, then press
    MENU/SELECT to confirm your selection.
    Monitor the temperature
    Minimum temperature
    You can set the desired minimum room
    temperature of the baby unit. The minimum
    temperature can be set between 52
    o
    F (11
    o
    C)
    and 69
    o
    F (20
    o
    C).
    To set the minimum temperature of the baby
    unit:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose TEMPERATURE,
    then press MENU/SELECT to select.
    Press or to choose Minimum, then
    press MENU/SELECT to select.
    Press or to choose a desired baby unit
    or all baby units.
    Press or to choose the desired
    temperature, then press MENU/SELECT to
    confirm your selection.
    1.
    2.
    3.
    4.
    1.
    2.
    3.
    4.
    1.
    2.
    3.
    4.
    5.
    Maximum temperature
    You can set the desired maximum room
    temperature of the baby unit. The maximum
    temperature can be set between 70
    o
    F (21
    o
    C)
    and 86
    o
    F (30
    o
    C).
    To set the maximum temperature of the baby
    unit:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose TEMPERATURE,
    then press MENU/SELECT to select.
    Press or to choose Maximum, then
    press MENU/SELECT to select.
    Press or to choose a desired baby unit
    or all baby units.
    Press or to choose the desired
    temperature, then press MENU/SELECT to
    confirm your selection.
    Temperature alert
    You can set whether the parent unit beeps
    whenever the temperature is out of the preset
    temperature range.
    To set the temperature alert of the baby unit:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose TEMPERATURE,
    then press MENU/SELECT to select.
    Press or to choose Alert, then press
    MENU/SELECT to select.
    Press or to choose a desired baby unit
    or all baby units.
    Press or to choose On or Off, then press
    MENU/SELECT to confirm your selection.
    Temperature format
    You can set the temperature scale of the baby
    unit.
    To change the temperature scale:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose TEMPERATURE,
    then press MENU/SELECT to select.
    Press or to choose Format.
    Press or to choose
    o
    F or
    o
    C, then press
    MENU/SELECT to confirm your selection.
    1.
    2.
    3.
    4.
    5.
    1.
    2.
    3.
    4.
    5.
    1.
    2.
    3.
    4.
    Adjust the sound sensitivity
    You can use the parent unit to change the
    sound sensitivity level of the baby units from
    Level 1 to
    Level 5. The higher the sound sensitivity level
    is set, the more sensitive the baby unit is in
    detecting sounds for transmitting to the parent
    unit.
    If you want the baby unit to be very sensitive in
    detecting sounds, you may set the sensitivity
    level to Level 5, so that the baby unit will always
    detect any sounds including background noises
    for transmitting to the parent unit. If you want
    the baby unit to be less sensitive in detecting
    sounds, you may set the sensitivity level to a
    lower level (Level 1 to Level 4), so that the baby
    unit will transmit sounds to the parent unit only
    when your baby is very noisy or crying loudly.
    To set the sound sensitivity level of the baby
    unit:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose SENSITIVITY, then
    press MENU/SELECT to select.
    Press or to choose a desired baby unit
    or all baby units.
    Press or to choose the desired
    sensitivity level, then press MENU/SELECT to
    confirm your selection.
    Sound Activation
    When the parent unit screen is turned off
    manually, you can set the screen to be turned
    on automatically whenever there are sounds
    detected from the baby units. The parent unit
    screen will turn off automatically when no
    sounds are detected from the baby units within
    50 seconds.
    To turn the sound activation on or off:
    Press MENU/SELECT when the parent unit is
    not in use.
    Press or to choose
    SOUND ACTIVATION.
    Press or to choose On or Off.
    If you set the sensitivity level to Level 5, the
    baby unit will be very sensitive and detect
    any sounds including background noises.
    These background noises may disrupt the
    silence and prevent the sound activation
    feature to work properly.
    1.
    2.
    3.
    4.
    1.
    2.
    3.
    Before use
    Using the baby monitor
    Overview
    Rotatable camera head
    Antenna
    Temperature
    sensor
    ON/OFF
    Camera
    Light sensor
    Speaker
    + (Volume up)
    - (Volume down)
    ON/OFF LED
    light
    1
    2
    3
    The bar
    keeps scrolling
    until charging is
    completed
    Self-adhesive
    strap
    Power outlet not
    controlled by a
    wall switch
    1
    2
    Bundle the power cord
    Power outlet not
    controlled by a
    wall switch
    BC
    Antenna
    MIC (Microphone)
    (Left)
    (Up)
    (On/off)
    (Right)
    (Down)
    Speaker
    VOL
    (Volume)
    (Zoom)/BACK
    (View)
    MENU/SELECT
    TALK
Vtech VM333-2

Need help?

Number of questions: 0

Do you have a question about the Vtech VM333-2 or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Vtech VM333-2 owners to properly answer your question.

View the manual for the Vtech VM333-2 here, for free. This manual comes under the category Baby Monitors and has been rated by 1 people with an average of a 6.5. This manual is available in the following languages: English. Do you have a question about the Vtech VM333-2 or do you need help? Ask your question here

ManualSearcher.com

Looking for a manual? ManualSearcher.com ensures that you will find the manual you are looking for in no time. Our database contains more than 1 million PDF manuals from more than 10,000 brands. Every day we add the latest manuals so that you will always find the product you are looking for. It's very simple: just type the brand name and the type of product in the search bar and you can instantly view the manual of your choice online for free.

ManualSearcher.com

© Copyright 2020 ManualSearcher.com. All Rights Reserved.

We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it.

Read more