Panasonic WV-SPW532L

Panasonic WV-SPW532L manual

(1)
  • Included Installation Instructions
    PoE device (hub)
    Adjustment monitor
    Ethernet cable
    (category 5e or better, straight)
    PC
    PC
    PGQX1993VA sL0915-4109 Printed in China
    IMPORTANT:
    Stretch the tape to approx. twice its length (see the
    illustration) and wind it around the cable. Insufficient
    tape stretch causes insufficient waterproofing.
    To prevent the Ethernet cable hook from coming
    loose easily, fit the LAN connector cover (
    B
    : accessory)
    onto the pigtail cable as illustrated, and then slide it in
    the direction indicated by the arrow. The connector of
    the Ethernet cable used with this camera must meet
    the following restrictions.
    Height when inserted (From bottom to hook.):
    Max. 16 mm {5/8 inches}
    Connector width: Max. 14 mm {9/16 inches}
    To install this product outdoors, be sure to waterproof
    the cables. Waterproof grade (IEC IP66 or equiva-
    lent) is applied to this product only when it is installed
    correctly as described in these operating instructions
    and appropriate waterproof treatment is applied. The
    camera mount bracket and camera arm are not
    waterproof.
    :
    Installation Guide
    Network Camera
    Model No.
    WV-SPW532L / WV-SPW312L
    This manual describes the installation procedures, network camera installation, cable
    connections, and eld-of-view adjustment.
    Before reading this manual, be sure to read the Important Information.
    This manual describes how to install the network camera using model WV-SPW532L as
    an example.
    Parts and functions
    The component names of the camera are as follows. Refer to the illustration when
    installing or adjusting the camera.
    Standard accessories Making connections
    Important Information ............................... 1 pc.
    Warranty card ........................................... 1 set
    Code label
    *2
    .............................................. 1 pc.
    Installation Guide (this document) ............ 1 set
    CD-ROM
    *1
    ................................................. 1 pc.
    *1
    The CD-ROM contains the operating instructions and different kinds of tool software programs.
    *2 This label may be required for network management. The network administrator shall retain
    the code label.
    A Template ......................................... 1 Sheet
    B LAN connector cover ........................... 1 pc.
    C Safety wire ........................................... 1 pc.
    D Wire lug fixing screw
    M3 × 10 mm {3/8 inches} ................... 2 pcs.
    (of them, 1 for spare)
    E Safety wire lug ..................................... 1 pc.
    F Auxiliary handle .................................... 1 pc.
    G Desiccant .........................................1 Sheet
    H Waterproof tape ................................... 1 pc.
    Turn off each system’s power supply before making a connection. Before making connections,
    prepare the required peripheral devices and cables.
    IMPORTANT:
    Use all 4 pairs (8 pins) of the Ethernet cable (category 5e or better, straight).
    The maximum cable length is 100 m {328 feet}.
    Make sure that the PoE device in use is compliant with IEEE802.3af standard.
    When the Ethernet cable is disconnected once, reconnect the cable after around 2
    seconds. When the cable is quickly reconnected, the power may not be supplied
    from the PoE device.
    When cables are used outdoors, there is a chance that they may be affected by light-
    ning. In this case, install a lightning arrester just before where the Ethernet cable
    connects to the camera.
    Connect an Ethernet cable (category 5e or better, straight)
    Waterproof treatment for the cable joint sections
    Adequate waterproof treatment is required for the cables when installing the camera with
    cables exposed or installing it under the eaves.
    The camera body is waterproof, but
    the cable ends are not waterproof.
    Be sure to use the supplied
    waterproof tape at the points where
    the cables are connected to apply
    waterproof treatment in the following
    procedure.
    Failure to observe this or use of
    a tape other than the provided
    waterproof tape (such as a vinyl tape)
    may cause water leakage resulting in malfunction.
    When connecting to a network using a PoE hub
    Before starting the installation, check the entire system conguration.
    The following illustration gives a wiring example of how to connect the camera to the network via
    a PoE device (hub).
    Stretch the tape to
    approx. twice its length.
    IMPORTANT:
    The adjustment monitor is used to adjust the field of view when installing or servicing
    the camera. It is not provided for recording/monitoring use.
    Depending on the adjustment monitor, some characters (camera title, preset ID, etc.)
    may not be displayed on the screen.
    Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
    The hook engages
    with the connector
    terminal
    LAN connector cover
    (
    B
    : accessory)
    *1 SDXC/SDHC/SD memory card is described as SD memory card.
    *2 Depending on the scanning application used, the Data Matrix may not be
    able to be read correctly. In this case, access the site by directly entering the
    following URL.
    http://security.panasonic.com/pss/security/support/qr_sp_select.html
    <Required cable>
    Ethernet cable (category 5e or better, straight)
    Use an Ethernet cable (category 5e or better, cross) when directly connecting the camera to a PC.
    For U.S. and Canada:
    Panasonic i-PRO Sensing Solutions
    Corporation of America
    800 Gessner Rd, Suite 700 Houston, TX 77024
    https://www.security.us.panasonic.com/
    Panasonic Canada Inc.
    5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada
    1-877-495-0580
    https://www.panasonic.com/ca/
    For Europe and other countries:
    Panasonic Corporation
    http://www.panasonic.com
    Panasonic i-PRO Sensing Solutions Co., Ltd.
    Fukuoka, Japan
    Authorised Representative in EU:
    Panasonic Testing Centre
    Panasonic Marketing Europe GmbH
    Winsbergring 15, 22525 Hamburg, Germany
    The following parts are used during installation procedures.
    RJ45 (female)
    Network cable
    Ethernet cable
    (category 5e or better,
    straight)
    © Panasonic i-PRO Sensing Solutions Co., Ltd. 2019
    <Ethernet cable>
    Wind the tape in a
    half-overlapping manner.
    Waterproof tape
    (H: accessory)
    WV-SPW532L
    TELE
    WIDE
    Auto focus (AF)
    button
    Two-dimensional
    matrix barcode
    (Data Matrix):
    To our website*
    2
    When the camera is able to communicate with the Lights orange
    connected device
    LINK indicator
    When data is being sent via the network camera Blinks green (accessing)
    ACT indicator
    When AF (Auto Focus) operation is being executed
    Blinks red (about once per second)
    When the camera is being started Lights red
    When an SD memory card
    *1
    is recognized normally
    Lights red → Lights off
    When the SD memory card slot is not used or an abnormality Lights red → Stays red
    is detected in SD memory card after the camera has started
    SD ERROR/AF indicator
    When an SD memory card is inserted and could Lights off → Blinks green →
    be recognized Lights off
    When data can be saved after the SD memory card is inserted Lights off → Lights green
    and the SD ON/OFF button is pressed (for less than 1 second)
    When data can be saved to the SD memory card Lights green
    When the SD memory card is removed after holding down
    Lights green → Blinks green →
    the SD ON/OFF button for about 2 seconds Lights off (recording)
    Lights green →
    Lights off (waiting for recording)
    When data cannot be saved to the SD memory card because Lights off
    an abnormality was detected or the SD memory card is
    configured not to be used
    SD MOUNT indicator
    ● How to initialize the camera
    Follow the steps below to initialize the network camera.
    1 Turn o the power of the camera. When using a PoE hub, disconnect the Ethernet cable from the
    camera.
    2
    Turn on the power of the camera while holding down the INITIAL SET button, and keep the INITIAL
    SET button held down till the SD MOUNT indicator is lit in green (more than 10 seconds). In about
    2 minutes after releasing the INITIAL SET button, the camera will start up and the settings including
    the network settings will be initialized.
    ● When the INITIAL SET button (i.e. the initializing button) is pressed (less than 1 second) to switch
    the output signal of the MONITOR OUT terminal (NTSC
    PAL output), the MONITOR OUT terminal
    can be switched for the NTSC monitor/PAL monitor.
    IMPORTANT:
    When the camera is initialized, the settings including the network settings will be initialized.
    Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not be initialized.
    Before initializing the settings, it is recommended to write down the settings in advance.
    Do not turn off the power of the camera during the process of initialization. Otherwise, it
    may fail to initialize and may cause malfunction.
    INITIAL SET button (Initializing / NTSC
    PAL switch button)
    1 When the SD ON/OFF button is pressed for less than 1 second, the SD MOUNT indicator is lit
    green and data can be saved to the SD memory card.
    2 When the SD ON/OFF button is held down for about 2 seconds, the SD MOUNT indicator goes
    out, and the SD memory card can be removed.
    SD ON/OFF button
    TILT lock screw
    Camera
    Front cover
    Safety wire (C: accessory)
    Sunshield
    Camera mount
    bracket
    Camera Arm
    PAN lock screw
    [2] Remove the front cover
    Installation
    Step 1 Before starting the installation
    The installation tasks
    are explained using
    5 steps.
    Tear off the blue tape attached on camera arm before installing the camera.
    Prepare the required parts for installation method before starting the installation. The
    following is the requirements for the installation method.
    Installation method
    Recommended
    screw
    Minimum pull-
    out strength
    Directly mount the camera onto the ceiling or
    wall (when there is a space for wiring in the
    ceiling or the wall)
    M4 screws × 3
    724 N {163 lbf}
    (per 1 pc.)
    *1
    *1 To mount the camera onto the ceiling or wall, the safety wire (C: accessory)
    must be attached. Have an M6 bolt and nut or anchor (with the minimum pull-
    out strength of 724 N {163 lbf}) ready for securing the safety wire.
    Step 1
    Before starting the
    installation
    Step 2
    Preparation
    Step 3
    Fixing the camera
    Step 4
    Adjusting the camera
    Step 5
    Congure the network
    settings
    IMPORTANT:
    For the screws or anchor bolts used in the above method, be sure to secure the mini-
    mum pull-out strength of 724 N {163 lbf} per screw or bolt.
    Select screws according to the material of the ceiling or wall that the camera will be
    mounted to. In this case, wood screws and nails should not be used.
    If a ceiling or wall board such as plaster board is too weak to support the total weight,
    the area shall be sufficiently reinforced.
    Because the front cover is temporarily removed when installing or adjusting the camera,
    make sure no liquid enters the camera at these times.
    Loosen the 4 front cover fixing screws, and then remove the front cover.
    1
    Pass the safety wire (
    C
    : accessory)
    through the wire mounting hole in
    the safety wire lug (E
    :
    accessory).
    Wire mounting hole
    Front cover fixing screws
    Front cover
    [1] Attaching the safety wire
    Step 2 Preparation
    Safety wire lug
    (
    E
    : accessory)
    Safety wire
    (
    C
    : accessory)
    Wire fitting
    Wire lug fixing screw
    (
    D
    : accessory)
    Safety wire lug
    (
    E
    : accessory)
    2 Fit the Safety wire lug to the camera.
    Recommended tightening torque:
    0.59 N·m {0.44 lbf·ft}
    * The safety wire is not shown in the
    subsequent illustrations.
    YAW lock screw
    Name plate
    Zoom knob
    MONITOR OUT jack
    (Video Out terminal
    Default:
    For NTSC monitor)
    SD memory card slot
    IR LED
Panasonic WV-SPW532L

Need help?

Number of questions: 1

Do you have a question about the Panasonic WV-SPW532L or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Panasonic WV-SPW532L owners to properly answer your question.

David Bruton, 2020-09-12 17:40:30 No comments

I have the POE cable coming out of the wall and wish to connect this inside the camera. I am unable to use the cable connector provided without drilling large holes in the wall and installing an internal junction box. Please can you provide instructions?

Answer this question

View the manual for the Panasonic WV-SPW532L here, for free. This manual comes under the category Security cameras and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Panasonic WV-SPW532L or do you need help? Ask your question here

Panasonic WV-SPW532L specifications

General
Brand Panasonic
Model WV-SPW532L
Product Security camera
EAN 4010869211277, 4549077602268, 0885170265479
Language English
Filetype PDF
Video
Video formats supported H.264
Video compression formats H.264
Noise reduction
Full HD
Maximum resolution 2048 x 1536
Frame rate 30
Supported graphics resolutions 1920 x 1080 (HD 1080), 2048 x 1536 (QXGA)
Supported video modes 1080p
Night vision
LED type IR
Night vision
Lens system
Auto focus
Maximum aperture number 1.6
Focal length range 2.8 - 10mm
Optical zoom 3.6
Storage
Built-in HDD
Card reader integrated
Compatible memory cards SD, SDHC, SDXC
Security
Video motion detection
Security algorithms SSL/TLS
Design
International Protection (IP) code IP66
Weatherproof
Protection features Dust resistant, Water resistant
Form factor Bullet
Product colour Chrome
Mounting type Ceiling/Wall
Image sensor
Sensor type MOS
Optical sensor size 1/3 2011-05-04 11:27:54 2012-06-08 13:40:02 12 28 1 RPM 0000-00-00 00:00:00 2012-06-08 13:40:02 14 30 1 M 0000-00-00 00:00:00 2012-06-08 13:40:02 15 31 1 kHz 0000-00-00 00:00:00 2012-06-08 13:40:02 16 32 1 ° 0000-00-00 00:00:00 2012-06-08 13:40:02 17 33 1 x
Performance
Day/night mode
Type IP security camera
Placement supported Indoor & outdoor
Connectivity technology Wired
Camera
Minimum illumination 0.07
Tilt angle range -90 - 90
Pan range -90 - 90
Power
Power over Ethernet (PoE)
Power source type PoE
Network
Ethernet LAN
Wi-Fi -
Packaging content
Number of cameras 1

Frequently Asked Questions

Below, you will find the most frequently asked questions about the Panasonic WV-SPW532L.

Is your question not listed? Ask your question here

ManualSearcher.com

Looking for a manual? ManualSearcher.com ensures that you will find the manual you are looking for in no time. Our database contains more than 1 million PDF manuals from more than 10,000 brands. Every day we add the latest manuals so that you will always find the product you are looking for. It's very simple: just type the brand name and the type of product in the search bar and you can instantly view the manual of your choice online for free.

ManualSearcher.com

© Copyright 2020 ManualSearcher.com. All Rights Reserved.

We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it.

Read more