JVC RD-N1W manual

  • ID3 ON ID3 OFF
    CAUTION: Proper Ventilation
    To avoid risk of electric shock and fire, and to prevent damage,
    locate the apparatus as follows:
    Front: No obstructions and open spacing.
    Sides/Top/Back: No obstructions should be placed in the
    areas indicated by the dimensions in the illustration.
    Bottom: Place on the level surface. Maintain an adequate air
    path for ventilation by placing on a stand with a height of
    10 cm or more.
    ATTENTION: Aération correcte
    Pour prévenir tout risque de décharge électrique ou d’incendie
    et éviter toute détérioration, installez l’appareil de la manière
    Avant: Bien dégagé de tout objet.
    Flancs/ Dessus/ Arrière: Aucun obstacle ne doit être
    placé dans les zones indiquées par les dimensions dans
    Dessous: Posez l’appareil sur une surface plane et
    horizontale. Veillez à ce que sa ventilation correcte puisse
    se faire en le plaçant sur un support d’au moins dix
    centimètres de hauter.
    Side view/Côté
    Front view/Face
    Microsoft and Windows Media are either registered
    trademarks or trademarks of Microsoft Corporation in
    the United States and/or other countries.
    iPod is a trademark of Apple Inc., registered in the U.S.
    and other countries.
    “Made for iPod means that an electronic accessory
    has been designed to connect specifically to iPod and
    has been certified by the developer to meet Apple
    performance standards.
    Apple is not responsible for the operation of this device
    or its compliance with safety and regulatory standards.
    Thank you for purchasing a JVC product.
    LVT2130-002B [J, C, B, US, A, UX]
    ©2010 Victor Company of Japan, Limited
    SLEEP 10 SLEEP 20 SLEEP 30
    SLEEP 90
    File Title
    For customer use:
    Enter below the Model No. and Serial No. which are
    located either on the rear, bottom or side of the cabinet.
    Retain this information for future reference.
    Model No.
    Serial No.
    For USA-California Only
    This product contains a CR Coin Cell Lithium Battery
    which contains Perchlorate Material—special handling
    may apply.
    See www.dtsc.ca.gov/hazardouswaste/perchlorate
    Sound Mode
    To select the sound mode suitable for your favorite
    Setting the clock
    You can set the clock only when the System is turned
    off (on standby.)
    If you have already set the clock before, press and
    hold CLOCK until the clock is flashing.
    2 Adjust the hour and minute.
    The clock may gain or lose 1 to 2 minutes per month.
    You may need to readjust the clock periodically.
    Compatible iPod models
    iPod model Audio
    iPod nano
    iPod nano (2nd Generation)
    iPod nano (3rd Generation)
    iPod nano (4th Generation)
    iPod nano (5th Generation)
    iPod mini
    iPod mini (2nd Generation)
    iPod (4th Generation)
    iPod classic
    iPod photo (4th Generation)
    iPod video (5th Generation)
    iPod touch
    iPod touch (2nd Generation and Fall ‘09)
    If iPod does not play correctly, update iPod software to the
    latest version.
    For details about updating iPod, check on the Apple web
    site <http://www.apple.com>.
    To get the best performance of the System, keep your discs
    and the mechanism clean.
    Handling discs
    Remove the disc from its case by holding it at the edge
    while pressing the center hole lightly.
    Do not touch the shiny surface of the disc, or bend the
    Put the disc back in its case after use.
    Be careful not to scratch the surface of the disc when
    placing it back in its case.
    Avoid exposure to direct sunlight, temperature extremes,
    and moisture.
    To clean the disc:
    Wipe the disc with a soft cloth in a straight line from center
    to edge.
    Cleaning the System
    Stains should be wiped off with a soft cloth. If the System
    is heavily stained, wipe it with a cloth soaked in water-
    diluted neutral detergent and wrung well, then wipe
    clean with a dry cloth.
    Since the System may deteriorate in quality, become
    damaged or get its paint peeled off, be careful about the
    DO NOT wipe it hard.
    DO NOT wipe it with thinner or benzine.
    DO NOT apply any volatile substances such as
    insecticides to it.
    DO NOT allow any rubber or plastic to remain in contact
    for a long time.
    Prepare the remote control
    When you use the remote control for the first time, pull out the insulation sheet.
    To replace the battery in the remote control
    Supplied accessories
    After unpacking, check to make sure that you have all
    the following items:
    Remote control (× 1)
    Lithium coin battery CR2025 (× 1)
    The battery has been installed in the remote
    control when shipped from the factory.
    FM antenna (× 1)
    AC plug adaptor (× 1) (Not supplied for USA,
    Canadian, European, Australian and Saudi Arabian
    If anything is missing, consult your dealer immediately.
    Notes on the power cord
    When you go away for an extended period of time,
    remove the plug from the wall outlet.
    When unplugging the System from the wall outlet,
    always pull the plug, not the power cord.
    Do not handle the power cord with wet hands.
    Disconnect the power cord before cleaning the System or
    moving the System.
    Do not alter, twist or pull the power cord, or put anything
    heavy on it, which may cause fire, electric shock, or other
    Avoid moisture, water, dust, and high temperatures
    Do not place the System in moist or dusty places.
    If water gets inside the System, turn off the power and
    remove the plug from the wall outlet, then consult your
    dealer. Using the System in this state may cause a fire or
    electrical shock.
    Do not expose the System to direct sunlight or place it
    near a heating device.
    Lithium coin battery
    (product number: CR2025)
    Store the battery in a place where children cannot reach. If a child accidentally
    swallows the battery, consult a doctor immediately.
    To prevent the battery from overheating, cracking, or starting a fire:
    Do not recharge, short, disassemble or heat the battery or dispose of it in a
    Do not leave the battery with other metallic materials.
    Wrap the battery with tape and insulate when throwing away or saving it.
    Do not poke the battery with tweezers or similar tools.
    Dispose of battery in the proper manner, according to federal, state, and local
    The battery (battery pack or battery installed) shall not be exposed to excessive
    heat source such as sunshine, fire or the like.
    Danger of explosion if battery is incorrectly replaced. Replace only with the same
    or equivalent type.
    Getting started
    For better FM reception
    Disconnect the supplied FM antenna, and connect to an outdoor FM antenna (not supplied)
    using a 75 Ω wire with coaxial type connector (IEC or DIN45325).
    To a wall outlet
    FM antenna (supplied): Extend it so that you can obtain the best reception.
    Make sure the antenna conductors do not touch any other terminals, connecting cords
    or the power cord. Also, keep the antennas away from metallic parts of the System,
    connecting cords, and the AC power cord. Otherwise, it could cause poor reception.
    Sound and other adjustments
    Connections Do not connect the AC power cord until all other connections have been made.
    In this manual...
    The remote control buttons are used for explaining the
    operations unless mentioned otherwise. However, if the
    System has the same or similar button names, they can
    also be used for the operations.
    “File and “track” are used interchangeably.
    All the illustrations of the display used as examples are
    from the European models.
    Amplifier section
    Output Power: 6 W (3 W + 3 W) at 3 Ω (10% THD)
    Audio Input: AUDIO IN: Stereo mini (ø 3.5 mm)
    250 mV/47 kΩ
    Digital input: USB MEMORY
    FM tuning range: 87.50 MHz – 108.00 MHz
    Disc player
    Dynamic range: 80 dB
    Wow and flutter: Immeasurable
    USB specification: Compatible with USB 2.0 Full Speed
    Compatible device: Mass storage class
    Compatible system: FAT16, FAT32
    Output power: DC 5 V
    500 mA
    Output power: DC 5 V
    500 mA
    Speaker type: Bass-Reflex type
    Speaker unit: 9 cm (3–9/16 inches) x 2
    Speaker impedance: 3 Ω
    Power requirements:
    For USA and Canadian models AC 120 V / 60 Hz
    For European models AC 230 V / 50 Hz
    For Australian models AC 240 V / 50 Hz
    For other models AC 110 V – 127 V / 220 V – 240 V
    adjustable with voltage selector, 50/60 Hz
    Power consumption: 35 W (at operation)
    1.00 W or less (on standby)
    Dimensions (approx.): 400 mm × 141 mm × 211 mm
    (15–3/4 inches × 5–9/16 inches × 8–5/16 inches)
    (W × H × D)
    Mass (approx.): 3.3 kg (7.3 lbs)
    If you are having a problem with your System, check this list for a possible solution before calling for service.
    Power does not come on. \ Power plug is not inserted securely. Plug it in securely.
    Adjustments or settings are suddenly
    canceled before you finish.
    \ There is a time limit. Start the procedure again.
    Unable to operate the System from the
    remote control.
    \ The path between the remote control and the remote sensor on the
    System is blocked.
    \ The battery is exhausted.
    No sound is heard. \ Headphones are connected.
    FM radio
    Hard to listen to broadcasts because of
    \ Antenna connection is incorrect or loose.
    \ The FM antenna is not properly extended and positioned.
    \ Electrostatic discharge from your body may cause noise. If this
    happens, turn the System off then on again.
    The iPod does not play, but “IPOD”
    appears on the display.
    \ The iPod battery is low or exhausted. Charge the iPod battery.
    The disc/USB mass storage class device
    does not play.
    \ The disc is placed upside down. Place the disc with the label side
    facing up.
    \ The disc is recorded using “packet writing (UDF file system). It cannot
    be played.
    \ The USB mass storage class device is not connected properly.
    “NO SONG” appears on the display. \ MP3/WMA files are not recorded on the disc or USB mass storage class
    ID3 Tag on an MP3 file cannot be shown. \ There are two types of ID3 Tag—Version 1 and Version 2. This System
    can only show ID3 Tag Version 1.
    Groups and tracks are not played back as
    you expect.
    \ Playing order is determined when the groups and tracks are recorded.
    It depends on the writing application.
    The disc/USB mass storage class device
    sound is discontinuous.
    \ The disc is scratched or dirty.
    \ MP3/WMA files have not been properly recorded onto the USB mass
    storage class device.
    Sound from the USB mass storage class
    device is interrupted.
    \ Noise and static electricity may stop the sound. In this case, disconnect
    and connect the USB mass storage class device again after turning off
    the System.
    The disc tray does not open or close. \ The AC power cord is not plugged in.
    \ Disc ejection is prohibited. “DISC LOCKED appears (see “Prohibiting
    disc ejection” in “Disc/USB” on page 2).
    Unable to record onto a USB mass
    storage class device.
    \ The capacity of the USB mass storage class device is full.
    \ The USB mass storage class device is write-protected.
    If the System does not work correctly, disconnect the AC power cord from the wall outlet, wait for a while, then
    connect the cord again.
    JVC bears no responsibility for any loss of data in USB mass storage class device or iPod while using this System.
    Initial settings
    Playable disc/file types
    This System can play back...
    Audio CD and CD-R/CD-RW in Audio CD format
    MP3/WMA files on a CD-R/CD-RW (ISO 9660 format) or
    USB mass storage class device (maximum data transfer
    rate: 2 Mbps)
    This System cannot play “packet write discs.
    For MP3/WMA playback...
    Some MP3/WMA files may not be played back due to
    their recording conditions.
    This System can play only discs of ISO 9660 Level 1 or
    Level 2.
    It is recommended to record each file at a sampling rate
    of 44.1 kHz and at a data transfer rate of 128 kbps.
    This System can recognize a total of 999 tracks and 99
    This System can show the Tag data (version 1).
    For playback of files on a USB mass storage class device...
    You cannot play back files larger than 2 GB.
    This System may not play back some USB mass storage
    class devices and does not support DRM (Digital Rights
    To check the current time while the System is turned
    The time is displayed for a few seconds.
    If there is a power failure
    The clock loses its settings. You need to set the clock
    Display settings
    Display information
    To display ID3/WMA tag information
    During playback of MP3/WMA...
    ID3/WMA tag information is displayed automatically
    as follows:
    Sleep Timer
    You can set Sleep Timer only when the System is turned
    2 Specify the time.
    To check the remaining time until the System shuts
    off, press and hold CLOCK.
    Sound adjustments
    Fade muting
    To drop the volume in a moment
    To restore the volume, press again or adjust the
    Hyper Bass Sound (HBS)
    To reinforce the bass sound
    (Europe only)
    Notes on installation
    Select a place which is level, dry and neither too hot nor
    too cold—between 5˚C and 35˚C (41°F and 95 °F).
    Do not install the System in a place subject to vibrations.
    Do not put heavy objects on the System.
    To prevent malfunction or damage to the System
    Do not insert any metallic objects, such as wires, hairpins,
    coins, etc. into the System.
    Do not block the vents.
    There are no user-serviceable parts inside. If anything
    goes wrong, unplug the power cord and consult your
    Supplied accessories
    See “Supplied accessories” in “Getting started.
    Design and specifications are subject to change without
    When you replace the battery, place the
    edge of the battery under the wire loop.
    Wire loop
    (No indication)
    Mains (AC) Line Instruction (Asia and Saudi Arabia only)
    CAUTION for mains (AC) line
    BEFORE PLUGGING IN, do check that your mains (AC) line
    voltage corresponds with the position of the voltage selector
    switch provided on the outside of this equipment and, if
    different, reset the voltage selector switch, to prevent from a
    damage or risk of fire/electric shock.
    If the wall outlet does not match the AC plug, use the supplied AC plug adaptor.
    (Not supplied for USA, Canadian, European, Australian and Saudi Arabian models.)
    EN_RDN1[JCBUSAUX]REV_B_2nd.indd 1EN_RDN1[JCBUSAUX]REV_B_2nd.indd 1 10.7.28 0:56:57 PM10.7.28 0:56:57 PM

Need help?

Number of questions: 0

Do you have a question about the JVC RD-N1W or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other JVC RD-N1W owners to properly answer your question.

View the manual for the JVC RD-N1W here, for free. This manual comes under the category Speakers and has been rated by 1 people with an average of a 8.8. This manual is available in the following languages: English. Do you have a question about the JVC RD-N1W or do you need help? Ask your question here

JVC RD-N1W specifications

Brand JVC
Model RD-N1W
Product Speaker
Language English
Filetype PDF
Audio D/A Converter (DAC) 1-bit
Audio formats supported MP3, WMA
RMS rated power 6
Built-in speaker(s)
Digital tuner
Supported radio bands FM
Media types
CD-RW playback
CD-R playback
Preset stations quantity 20
Device type -
Compatible products iPod
Product colour White
Display LCD
ID3 Tag display
Management features
Sleep timer
Handheld remote control
Ports & interfaces
Audio input 1
USB 2.0 ports quantity 1
Power requirements 120V, 60Hz
Weight & dimensions
Weight 3300
Other features
Dimensions (WxDxH) 400 x 211 x 141mm

Frequently Asked Questions

Below, you will find the most frequently asked questions about the JVC RD-N1W.

Is your question not listed? Ask your question here


Looking for a manual? ManualSearcher.com ensures that you will find the manual you are looking for in no time. Our database contains more than 1 million PDF manuals from more than 10,000 brands. Every day we add the latest manuals so that you will always find the product you are looking for. It's very simple: just type the brand name and the type of product in the search bar and you can instantly view the manual of your choice online for free.


© Copyright 2020 ManualSearcher.com. All Rights Reserved.

We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it.

Read more