Drayton RTS9

Drayton RTS9 manual

  • RTS Thermostat
    Installation instructions
    RTS1: Standard heating thermostat
    RTS2 Heating thermostat with call for heat LED indicator
    RTS3: Indoor frost thermostat
    RTS4 Volt free heating/cooling change over switch
    RTS9 & 10: Volt free heating/cooling changeover switch with call
    for heating LED indicator
    RTS thermostats are ELECTRONIC with a relay output.
    Unless connected to a 230V mains supply the relay will
    not operate, no 'click' will be heard and the call for heat
    contact will remain open.
    Care should be taken to mount the thermostat in a position
    which is not subject to direct sunlight or draughts. Preferably
    it should be mounted on an inside wall about 1.5m (5ft)
    above the floor in a position where it can respond to room
    temperature but away from the direct influence of radiators
    or other appliances giving off heat.
    Note: If the thermostat is to be used as a frost protection
    device it should be located in the coldest part of the premises.
    1. Loosen the securing screws, remove the wall-plate and, if
    surface wiring is to be used, snap out the cable entry strip
    on the bottom edge of the wall-plate with a pair of pliers.
    2. Fix the wall-plate, terminals at the top, either direct onto a
    flat wall using wall plugs and No 6 x 1” woodscrews or on a
    flush mounting single conduit box using M 3.5 x 14 screws.
    3. Complete the wiring to the wall-plate in accordance with
    the relevant diagram shown overleaf in accordance with
    I.E.E. regulations.
    Note: The thermostat is for fixed wiring only and is double
    insulated, the earthing continuity (loop) terminal is only
    provided for convenience.
    4. Plug the thermostat onto the wall-plate and tighten the
    securing screws.
    5. Before switching on the mains ENSURE THE CIRCUIT
    FUSE IS 3A.
    Disconnect mains supply before fitting or removing from
    A switch having contact separation of at least 3mm in all
    poles must be incorporated in the fixed wiring as a means
    of providing full disconnection of the mains supply.
    1. Set the desired room temperature on the control knob
    against the setting mark.
    2. The setting range may be limited or a particular setting
    locked through the use of the mechanism to be found
    under the control knob.
    3. To adjust the limiters firstly set the thermostat to the
    desired temperature and then carefully pull off the knob.
    4. Lift and rotate the two limiting arms to re-position them in
    the required notches.
    5. Replace the knob with the previously set temperature
    against the setting mark.
    Technical data
    Electrical supply: 230V ac 50Hz fused 3A
    Double insulated (no earth required)
    Temp. range: RTS1, 2, 4 & 9 10° to 30°C
    RTS3 (Frost) 3° to 10°C
    Switch type: RTS 1, 2 & 3 S.P.S.T 2(1)A 230V ac live
    RTS4, 9 & 10 S.P.D.T 2(1)A 230V ac volt free
    Temp. sensor: Electronic
    14° to 30°C
Drayton RTS9

Need help?

Number of questions: 0

Do you have a question about the Drayton RTS9 or do you need help? Ask your question here. Provide a clear and comprehensive description of the issue and your question. The more detail you provide for your issue and question, the easier it will be for other Drayton RTS9 owners to properly answer your question.

View the manual for the Drayton RTS9 here, for free. This manual comes under the category Thermostat and has been rated by 1 people with an average of a 7. This manual is available in the following languages: English. Do you have a question about the Drayton RTS9 or do you need help? Ask your question here

Drayton RTS9 specifications

Brand Drayton
Model RTS9
Product Thermostats
Language English
Filetype PDF


Looking for a manual? ManualSearcher.com ensures that you will find the manual you are looking for in no time. Our database contains more than 1 million PDF manuals from more than 10,000 brands. Every day we add the latest manuals so that you will always find the product you are looking for. It's very simple: just type the brand name and the type of product in the search bar and you can instantly view the manual of your choice online for free.


© Copyright 2020 ManualSearcher.com. All Rights Reserved.

We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it.

Read more