Crestron HD-DA8-4KZ-E manual

View here the free Crestron HD-DA8-4KZ-E manual. Have you read the manual but does it answer your question? Then ask your question on this page to other Crestron HD-DA8-4KZ-E owners.

1:8 HDMI
Distribution Amplifier w/4K60 4:4:4 & HDR Support
> Splits one HDMI
source to eight outputs
> Handles 4K60 4:4:4 and HDR video signals
> Fully compatible with HD 1080p, UHD 4K, and
DCI 4K sources and displays
> Handles 3D video and Deep Color
> Handles Dolby
TrueHD, Dolby Atmos
, and uncompressed 7.1 linear PCM audio
> Selectable handling of HDCP 2.2 or HDCP 1.4
> EDID management options
> Input and output video presence indication
> No programming or control system required
> Thin profile – less than one inch deep
> Surface, shelf, or single rack rail mountable
> External 100-240V universal power pack included
The Crestron
HD-DA8-4KZ-E is a simple to use, high-performance 4K
AV distribution amplifier designed to split a single HDMI
signal to feed
up to eight separate displays, switchers, and/or other devices. It provides
full support for UHD and DCI 4K60 4:4:4 and HDR video, HDCP 1.4 or 2.2
copy protection, and high-bitrate 7.1 audio, to ensure optimal performance
and compatibility for any HD or 4K video application. No programming or
control system is required for operation.
For smaller applications, refer to models
HD-DA2-4KZ-E and HD-DA4-4KZ-E.
Input Signal Type: HDMI w/HDR10, Deep Color, 3D, & 4K60 4:4:4 support
(DVI & Dual-Mode DisplayPort compatible
Output Signal Type: HDMI w/HDR10, Deep Color, 3D, & 4K60 4:4:4
(DVI compatible
Copy Protection: Selectable for HDCP 2.2, HDCP 1.4, or HDCP disabled
Maximum Resolutions:
4096x2160 DCI 4K
3840x2160 4K UHD
24 Hz 4:4:4 36 bit
30 Hz 4:4:4 36 bit
60 Hz 4:2:2 36 bit
60 Hz 4:4:4 24 bit
2560x1600 WQXGA 60 Hz 4:4:4 36 bit
1920x1080 HD1080p 60 Hz 4:4:4 36 bit
Interlaced 1920x1080 HD1080i 30 Hz 4:4:4 36 bit
NOTE: Common resolutions are shown; other resolutions are supported at
pixel clock rates up to 600 MHz
Input Signal Type: HDMI (Dual-Mode DisplayPort compatible
Output Signal Type: HDMI
Formats: Dolby Digital
, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD,
Dolby Atmos, DTS
, DTS-ES, DTS 96/24, DTS HD High Res, DTS HD Master
Audio, DTS:X, LPCM up to 8 channels
USB: USB 2.0 host; supports firmware update and custom EDID upload
via a USB flash drive
HDMI: HDCP & EDID (does not pass CEC)
HDCP Version: Selectable for HDCP 2.2, 1.4, or OFF;
HDCP encrypted content is blanked in OFF mode
EDID Mode: Selectable for DEFAULT or COPY 1ST;
• The factory default EDID is 4K60 4:4:4 non-HDR video with
2-channel LPCM audio;
• The factory default EDID can be replaced with a custom EDID
via USB;
• Sliding the switch from DEFAULT to COPY 1ST copies and stores
the EDID from the device at OUTPUT 1 and passes it to the INPUT
source device;
• Sliding the switch from COPY 1ST to DEFAULT erases the stored
EDID and uses the factory default or custom EDID;
Note: Changing the device at OUTPUT 1 will not update the stored
EDID until the switch is moved to DEFAULT and back to COPY 1ST
INPUT: (1) HDMI Type A connector, female;
HDMI digital video/audio input
(DVI & Dual-Mode DisplayPort compatible
OUTPUT 1 – 8: (8) HDMI Type A connectors, female;
HDMI digital video/audio outputs
(DVI compatible
SERVICE: (1) USB Type A connector, female;
USB 2.0 host port;
For firmware update and custom EDID upload via a USB flash drive

Do you have a question about the Crestron HD-DA8-4KZ-E?

Ask the question you have about the Crestron HD-DA8-4KZ-E here simply to other product owners. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Crestron HD-DA8-4KZ-E owners to provide you with a good answer.