Brother PT-D200

Brother PT-D200 manual

  • ELECTRONIC LABELING SYSTEM
    Follow these guidelines to avoid the risk of fire, burns, injury, electric
    shocks, rupture, overheating, abnormal odours or smoke.
    Always use the specified voltage and the suggested AC adapter (AD-24ES) for the
    P-touch labeler to prevent any damage or failure.
    Do not touch the P-touch labeler during a lightning storm.
    Do not use the P-touch labeler/AC adapter in places of high humidity such as
    bathrooms.
    Do not overload the power cord.
    Do not place heavy objects on, or damage the power cord or plug. Do not forcibly
    bend or pull the power cord. Always hold the AC adapter when disconnecting from
    the power outlet.
    Make sure that the plug is fully inserted to the power outlet. Do not use an outlet that
    is loose.
    Do not allow the P-touch labeler/AC adapter/power plug/batteries to get wet, for
    example, by handling them with wet hands or spilling beverages on to them.
    Since loss of eyesight may result when leaked fluid from batteries gets into your eyes,
    immediately rinse your eyes with a large amount of clean water, and then seek
    medical attention.
    Do not disassemble or modify the P-touch labeler/AC adapter/batteries.
    Do not allow a metal object to contact both the plus and minus ends of a battery.
    Do not use sharp objects, such as tweezers or a metallic pen, to change the batteries.
    Do not throw the batteries into fire or expose to heat.
    Disconnect the AC adapter and remove batteries immediately and stop using the
    P-touch labeler if you notice abnormal odor, heat, discoloration, deformation or
    anything unusual while using or storing it.
    Do not use a damaged or leaking battery as the fluid may get on your hands.
    Do not use a deformed or leaking battery or one whose label is damaged. There is a
    possibility of generating heat.
    Follow these guidelines to avoid personal injury, liquid leakage,
    burns or heat.
    When the P-touch labeler is not being used, store it out of the reach of children. In
    addition, do not allow children to put the P-touch labeler parts or labels in their
    mouths. If any object has been swallowed, seek medical attention.
    Do not touch metal parts around the print head immediately after printing.
    Do not touch the cutter blade.
    If leaked fluid from batteries gets on your skin or clothes, immediately rinse them with
    clean water.
    Remove the batteries and disconnect the AC adapter if you do not intend to use the
    P-touch labeler.
    Do not use a battery other than that specified. Do not use combinations of old and
    new batteries or combinations of different types, different charging levels, different
    manufacturers or different models. Do not insert a battery with its plus and minus
    ends reversed.
    Do not drop or hit the P-touch labeler/AC adapter.
    Do not press on the LCD display.
    Do not put your finger inside the P-touch labeler when you close the cassette cover.
    Before using Ni-MH rechargeable batteries, carefully read the instructions for the
    batteries and battery charger, and be sure to use them correctly.
    When using Ni-MH rechargeable batteries, charge the batteries with a specialized
    battery charger before using the batteries.
    Depending on the location, material, and environmental conditions, the label may
    unpeel or become irremovable, the color of the label may change or be transferred
    to other objects. Before applying the label, check the environmental conditions and
    the material.
    Do not use the P-touch labeler in any way or for any purpose not described in this
    guide. Doing so may result in accidents or damage the P-touch labeler.
    Use only Brother TZe tapes with the P-touch labeler. Do not use tapes that do not
    have the mark.
    Only use a soft, dry cloth to clean the labeler; never use alcohol or other organic
    solvents.
    Use a soft wipe to clean the print head; never touch the print head.
    Do not put any foreign objects into the tape exit slot or AC adapter connector or
    battery compartment, etc.
    Do not place the P-touch labeler/batteries/AC adapter in direct sunlight or rain, near
    heaters or other hot appliances, in any location exposed to extremely high or low
    temperatures (e.g., on the dashboard or in the back of your car) or high humidity, or
    in dusty locations.
    Do not apply excessive pressure to the cutter lever.
    Do not try to print if the cassette is empty; it will damage the print head.
    Do not pull the tape while printing or feeding; it will damage the tape and the P-touch
    labeler.
    Any data stored in memory will be lost due to failure or repair of the P-touch labeler,
    or if the battery expires.
    The P-touch labeler is not equipped with a charging feature for rechargeable
    batteries.
    The printed text may differ from the text that appears in the LCD.
    The length of the printed label may differ from the displayed label length.
    A protective clear plastic sticker it placed over the display during manufacturing and
    shipping. This sticker should be removed prior to use.
    When power is disconnected for more than three minutes, all text, format settings and
    any text files stored in the memory will be cleared.
    Safety Precautions
    Indicates a potentially hazardous
    situation which, if not avoided,
    could result in death or serious
    injuries.
    WARNING
    Indicates a potentially hazardous
    situation which, if not avoided, may
    result in minor or moderate injuries.
    General Precautions
    CAUTION
    FCC NOTICE
    This device complies with Part 15 of the FCC Rules. Operation is subject to
    the following two conditions: (1) this device may not cause harmful
    interference, and (2) this device must accept any interference received,
    including interference that may cause undesired operation.
    This equipment has been tested and found to comply with the limits for a Class
    B digital device, pursuant to Part 15 of the FCC Rules. These limits are
    designed to provide reasonable protection against harmful interference in a
    residential installation. This equipment generates, uses, and can radiate radio
    frequency energy and, if not installed and used in accordance with the
    instructions, may cause harmful interference to radio communications.
    However, there is no guarantee that interference will not occur in a particular
    installation. If this equipment does cause harmful interference to radio or
    television reception, which can be determined by turning the equipment off
    and on, the user is encouraged to try to correct the interference by one or more
    of the following measures:
    Reorient or relocate the receiving antenna.
    Increase the separation between the equipment and receiver.
    Connect the equipment into an outlet on a circuit different from that to which
    the receiver is connected.
    Consult the dealer or an experienced radio/TV technician for help.
    Important
    Changes or modifications not expressly approved by Brother Industries,
    Ltd. could void the user’s authority to operate the equipment.
    Power Supply and Tape Cassette
    Open the cassette cover by pressing the
    above indicated area at the top end of the
    machine.
    If a tape cassette is already installed, remove it by
    pulling it straight up. Also, if batteries are already
    installed, remove them.
    Make sure that the power is turned off when
    replacing batteries or tape cassettes.
    Insert six new AAA alkaline batteries
    (LR03) or fully charged Ni-MH batteries
    (HR03), making sure that their poles
    point in the correct directions.
    Users of alkaline batteries:
    Always replace all six batteries at the
    same time with brand new ones.
    Users of Ni-MH batteries:
    Always replace all six batteries at the
    same time with fully charged ones.
    NOTE
    Visit us at http://solutions.brother.com/ for the latest
    information about the recommended batteries.
    Insert a tape cassette, making sure that
    it snaps into place.
    Make sure that the end of the tape feeds under
    the tape guides.
    Use only Brother TZe tapes with this machine.
    Securely close the cassette cover, making
    sure that it snaps into place.
    NOTE
    When using optional AC adapter (AD-24ES)
    1. Insert the plug on the adapter cord into the AC adapter
    jack on the top end of the machine.
    2. Insert the plug into the nearest standard electrical outlet.
    For memory back up, we recommend using AAA alkaline
    batteries (LR03) or Ni-MH batteries (HR03) together
    when using the AC adapter.
    1
    Print head
    Tape cutter
    lever
    Cassette
    cover
    2
    3
    Toothed
    Wheel
    Cutter’s
    edge
    End of tape
    Tape
    exit slot
    Tape guide
    4
    AC adapter jack
    NOTE
    The LCD shows one row of 15 characters; however, the text that
    you enter can be up to 80 characters in length.
    While selecting the settings, press Space key to go back to the
    default item.
    LCD Display & Keyboard
    1
    2
    3
    8
    9
    10
    11
    12
    13
    14
    15
    16
    17
    18 18
    4
    6
    5
    7
    19
    20
    21
    22
    23
    24
    25
    26
    27
    28
    1. Size
    2. Cursor
    3. Underline/Frame
    4. Width
    5. Style
    6. Caps
    7. Label Length
    If a specific label length has been
    selected, also appears.
    8. Cursor key : Right (Use with
    Shift key to go to end of the
    text.)
    9. OK key
    10. Escape key
    11. Cursor key : Left (Use with
    Shift key to go to top of the
    text.)
    12. Power key
    13. Menu key
    14. Font key
    15. Character key
    16. Tab key
    17. Caps key
    18. Shift key
    19. File key
    20. Print key
    21. Preview key
    22. Frame key
    23. Symbol key
    24. DECO MODE key
    25. Backspace key
    26. Enter key
    27. Accent key
    28. Space key
    The print preview is a generated image of the label, and may
    differ from the actual label when printed.
    Label length shown on LCD may slightly differ from the actual
    label length when printed.
    1 Start your machine.
    Supply power by using six AAA batteries or the optional AC
    adapter (AD-24ES), and then press .
    2 Set the language.
    The default setting is [English].
    3 Set the unit of measurement.
    The default setting is [inch].
    NOTE
    The machine automatically turns off if no keys are pressed within
    five minutes.
    To cancel any operation, press .
    Initial Settings
    / [Language]
    / [English/Español/Français/Hrvatski/
    Italiano/Magyar/Nederlands/Norsk/Polski/Português/
    Portug. (BR)/Românã/Slovenski/Slovenský/Suomi/
    Svenska/Türkçe/Čeština/Dansk/Deutsch] .
    / [Unit]
    / [inch/mm] .
    Troubleshooting
    X Error message X What to do when...
    Message Cause/Remedy
    Low Battery!
    The batteries are weak.
    If using AAA alkaline batteries: Replace them with new
    ones.
    If using Ni-MH batteries: Charge them fully.
    Battery Dead
    The installed batteries are running low.
    Invalid!
    There is no text above the cursor when you selected
    [Numbering].
    Invalid character is selected for [Numbering].
    Invalid number is selected for [Tab Length] or [Label
    Length].
    An invalid value was entered as the label length while
    using the DECO MODE or Name Label function.
    No Text!
    You tried to print a text file when there is no data
    stored in the memory.
    is pressed when no text is entered.
    You tried to select [Numbering], [Mirror], or Text
    Preview when no text is entered.
    or was pressed when no text was
    entered while using the DECO MODE or Name Label
    function.
    Line Limit!
    You tried to enter a 3rd line by pressing .
    You tried to print or preview two lines of text while
    0.13" (3.5mm) or 0.23" (6 mm) tape is installed. Install
    tape of a larger size.
    No Cassette!
    You tried to print a label when there is no cassette
    installed.
    Cutter Error
    Tape cutter lever is used in the middle of printing
    process.
    Text Full!
    The maximum number of characters (80 characters, 50
    characters for DECO MODE or Name Label function)
    have already been entered.
    Text Limit!
    With the DECO MODE or Name Label function:
    Since the number of entered characters exceeds the
    label length, reduce the text.
    All other functions:
    Since the number of entered characters exceeds the
    label length, reduce the text, or select [Auto] as the
    label length.
    No Frame OK?
    Printing on 0.13" (3.5mm) tape with invalid Frame
    setting ON. (Select to print with no Frame,
    to cancel.)
    OK to Feed?
    Feeding tape after printing when [Chain Print] is
    selected. Refer to “Setting Margin”.
    Insert 0.47"
    Only 0.47"(12mm) tape cassette is available for DECO
    MODE or Name Label function.
    Wrong Tape!
    Use a tape cassette with the mark.
    Message Cause/Remedy
    Problem Solution
    The display
    stays blank
    after you have
    turned on the
    machine.
    Check that the batteries are correctly inserted.
    If the batteries are weak, replace them.
    Check that the AD-24ES adapter is correctly
    connected.
    When the label
    is printed out,
    there is too
    much margin
    (space) on both
    sides of the text.
    See “Setting Margin” in this users guide and select
    [Half] or [Narrow] to have smaller margins for your
    label.
    The machine
    does not print,
    or the printed
    characters are
    not formed
    properly.
    Check that the tape cassette has been inserted
    correctly.
    If the tape cassette is empty, replace it.
    Check the cassette cover is properly closed.
    The setting has
    cleared on its
    own.
    The batteries may be weak. Replace them.
    When power is disconnected for more than three
    minutes, all text & formats in the display will be lost.
    Language and Unit settings will also be cleared.
    A blank
    horizontal line
    appears
    through the
    printed label.
    There maybe some dust on the print head. Remove
    the tape cassette and use a dry cotton swab to gently
    wipe the print head with an up-and-down motion.
    The machine
    has “locked up”
    (i.e., nothing
    happens when
    a key is
    pressed, even
    though the
    machine is on.)
    Refer to “Resetting the P-touch”.
    The power
    turns off when
    you try to print.
    The batteries may be weak. Replace them.
    Check that the batteries are correctly inserted.
    A wrong adapter is used; the recommended adapter
    is the AD-24ES.
    The tape does
    not feed
    properly or the
    tape gets stuck
    inside the
    machine.
    Check that the end of the tape feeds under the tape
    guides.
    The cutter lever is used while printing. Do not touch
    the cutter lever during printing.
    All text and
    format settings
    need to be
    cleared to
    create a new
    label.
    Press + and select [Text&Format].
    To change
    language
    setting.
    Refer to “Initial Settings”.
    Problem Solution
    BASIC USAGE
    X Switching Upper Case/Lower Case
    Upper case ( ON) Lower case ( OFF)
    X Making Two Lines of Text
    Move the cursor to where the second line starts and press .
    Use either 0.35" (9mm) or 0.47" (12mm) wide tape for two line text.
    NOTE
    The return symbol( ) will be displayed when the Enter key is
    pressed.
    X Entering Tab
    You can also set a tab by pressing .
    To change tab length:
    X Entering Accented Characters
    Refer to the table of accented characters (B) on the enclosed
    insertion sheet for a list of available accented characters.
    To cancel operations, press .
    The order of accented characters differs by the selected LCD
    language.
    X Changing Label Length
    NOTE
    After the label is printed, cut along the printed dots (:) with
    scissors so that the label length matches the machine setting.
    If a specific label length has been selected, also appears in
    the LCD.
    X To Clear
    By pressing , the letters will be deleted one by one.
    To delete all text and settings :
    To delete text only :
    X Preview
    You can preview the text before printing.
    The print preview is a generated image of the label, and may
    differ from the actual label when printed.
    When the LCD cannot display all the text at a time, press
    / to display the hidden text.
    X Feeding (Tape Feed)
    X Printing
    If you need only 1 copy of the label, press without
    selecting the number of copies.
    The number of copies can also be specified by pressing a
    number key.
    To prevent damage to the tape, do not touch the cutter lever
    while the message "Printing..." or "Feeding..." is displayed.
    To cut off the label, push in the tape cutter lever on the upper-
    right corner of the machine.
    To remove the backing, fold the label lengthwise with the text
    facing inward, to expose the inside edges of the backing.
    Peel off the backing one piece at a time and apply.
    You can print up to 9 copies of each label.
    X Using Print Options ( + )
    [Numbering]
    You can print many copies of the same text while increasing a
    selected number by 1 after each label is printed.
    Example: To print copies of a label containing a serial number
    (0123, 0124 and 0125)
    Select the highest number you wish to be printed when
    setting the number.
    [Mirror]
    Use clear tape in [Mirror], so the labels can be read correctly
    from the opposite side when attached on glass, windows or
    other transparent surfaces.
    X Setting Margin ( + )
    [Full]/[Half]/[Narrow]
    For leaving equal margins on both sides of the text.
    [Chain Print]
    For creating a label containing text in various styles.
    1. Enter text.
    2. Press , then [Copies: ] appears.
    3. Press / or enter number with number
    keys to select the number of copies.
    4. Press . Printing will start, and then the message
    "OK to Feed?" appears.
    5. Press to enter more text.
    6. Clear the text, enter the text for the next label, and then
    press .
    7. When the message "OK to Feed?" appears after the last
    label is printed, press .
    8. After the tape is fed, press the cutter lever to cut off the
    chain of labels.
    NOTE
    When [Chain Print] is set, feed the tape before using the cutter
    otherwise a part of the text may be cut off. Also, cut along the
    printed dots ( ) with scissors so the text is centered in the label.
    When [Half] or [Narrow] is set, displayed label length is the
    length from the printed dots ( ) to the end of the label.
    To print more than 1 copy of a label with minimum margin, set
    the margin to [Narrow].
    Do not pull the tape since this may damage the tape cassette.
    You can save up to 30 labels and recall them for printing at a later
    date. A maximum of 80 characters can be saved per file, a
    maximum total of 2400 characters for the total memory. You can
    also edit and overwrite the stored label.
    X Save
    X Print
    X Open
    You can also enter the File menu by pressing .
    NOTE
    If you try to store a label when there is already a label stored to that
    number, a message “Overwrite?” will appear. Press to
    save your new label. Press to cancel.
    If the cutter blade becomes blunt after repetitive use and the tape
    cannot be cut cleanly, replace with new cutter unit (stock no. TC-4) by
    obtaining from an authorized Brother reseller.
    X Replacing the Cutter Unit
    1. Pull out the two sections of the cutter unit (green) in the
    direction of the arrows shown in the illustration.
    2. Install a new cutter unit. Push it in until it snaps into place.
    Entering Text
    Line 1 Label image
    Line 2
    / [Tab]
    / [Tab Length]
    / [Auto/0.0"-4.0" (0-100 mm)]
    Caps
    Caps
    - / /
    / [Label Length]
    / [Auto/1.2"-12.0" (30-300 mm)]
    + / [Text&Format]
    + / [Text Only]
    Printing Labels
    +
    [Copies: ] / -
    / +
    / [Numbering]
    /
    + / [Mirror]
    [Mirror Print?]
    / [Margin]
    / [Full/Half/Narrow/Chain Print]
    LCD display Label image
    Full
    Half
    Narrow
    1"
    0.16"0.16"
    1"
    ABC ABC
    0.47" 0.47"
    ABC
    Full
    Half
    Narrow
    2.7"
    ABC
    1.6"
    ABC
    1"
    ABC
    Saving Label Files
    / [Save]
    /
    / [Print]
    /
    [Copies: ] / -
    / [Open]
    /
    Accessories
    Tape Cassettes: See the included “Supplies and
    Accessories Guide”.
    AC Adapter: AD-24ES
    Cutter Unit: TC-4 (replacement)
    Do not touch the cutter blade directly with your fingers.
    USING TEMPLATES
    This function allows you to create various name labels using the
    built-in templates. Refer to the Name Label format table (D) on the
    enclosed insertion sheet.
    Example:
    This function allows you to create unique labels by using built-in
    templates. Refer to the DECO MODE format table (C) on the
    enclosed insertion sheet.
    Example:
    NOTE
    Depending on the format you have selected, the entire
    contents of your text may not be printed. For example, if you
    selected a fixed Label Length and the text is too long, an error
    message "Text Limit!" will appear.
    The templates cannot be edited.
    Only the highlighted symbols on the enclosed insertion sheet
    can be used in DECO MODE.
    To clear all text, press and , then “Clear?” appears.
    Press to clear. Press to cancel.
    When you access DECO MODE or Name Label function, your
    most recently printed DECO MODE or Name Label function
    text and label length will be recalled.
    Press to return to the previous step.
    To exit the DECO MODE or Name Label function and return to
    the text input screen, do one of following:
    a) Press .
    b) Press / to select [Cancel], and then press
    when "Print" appears.
    These features are only available when using 0.47" (12mm)
    wide tape cassettes.
    The maximum label length is 7.8" (200mm) for DECO MODE
    and Name Label function.
    When [Auto] is selected for “Label Length”, the label will
    automatically adjust to the correct length for printing the text
    one time.
    Press to return to the [Auto] setting for “Label
    Length” mode.
    USEFUL FUNCTION KEYS
    1 Press to select the settings to enter
    the text.
    2 Press / to select the settings.
    * When [HEL + Atlanta], for example, is selected, the font for
    characters, including accented characters, will be Helsinki, and
    the font for numbers and some symbols will be Atlanta. Other
    combined fonts will be divided in the same way.
    NOTE
    To cancel operations, press .
    Refer to the font sample table (F) on the enclosed insertion sheet.
    The actual printed font size depends on the tape width, number of
    characters and number of input lines. Once characters reach a
    minimum size, the selected font will default to a custom font which
    is based on the Helsinki style. This allows labels to print using the
    smallest text possible on narrow or multi-line labels.
    Press to select the frame design. Refer to the frame
    design table (E) on the enclosed insertion sheet.
    NOTE
    To cancel operations, press .
    Press to select various symbols. Refer to the table of
    symbols (A) on the enclosed insertion sheet for a list of available
    symbols.
    NOTE
    To cancel operations, press .
    You can reset the P-touch labeler when you want to initialize the
    settings, or in the event the P-touch labeler is not working
    properly.
    1 Turn off the P-touch labeler, hold down
    and and then press to turn the P-touch
    back on.
    2 Release and .
    The P-touch labeler turns on with the internal memory reset.
    NOTE
    All text, settings and stored files are cleared.
    Name Label
    / [Name Label]
    [Select Layout] /
    Bill Anderson
    ABC Company, Inc.
    /
    [Auto/1.2" - 7.8" (30 -200mm)]
    [Print]
    DECO MODE
    [Select Layout]
    /
    [Input Text] ABCDEF
    / [Auto/1.2"-7.8"(30-200mm)]
    [Print]
    Font Key
    / Select an item
    Font
    Helsinki
    Brussels
    US
    Florida
    Belgium
    San Diego
    Los Angeles
    Calgary
    HEL + Atlanta *
    HEL + Adams *
    HEL + Brunei *
    HEL + Istanbul *
    HEL + Sofia *
    HEL + Germany *
    Size
    Large
    Medium
    Small
    Width
    Normal
    × 2
    × 1/2
    Style
    Normal
    Bold
    Outline
    Shadow
    Solid
    Italic
    I+Bold
    I+Outline
    I+Shadow
    Vertical
    Frame Key
    / Select a frame
    Symbol Key
    / [Basic/Pictograph]
    / Select category /
    Choose a symbol
    Short Cut Keys
    Language
    Label Length
    Margin
    Name Label
    File
    Tab
    Tab Length
    Clear
    Unit
    Resetting the P-touch
    With your PT-D200, you can create labels for multiple
    applications. Select from the many frames, character sizes and
    styles to design beautiful custom labels. In addition, the variety
    of tape cartridges available allows you to print labels with
    different widths and exciting colors.
    Read this manual carefully before starting and keep the manual
    in a handy place for future reference.
    Printed in China
    LAA723001A
    English
    Español
    User’s Guide
    Should you encounter any problems with your product,
    please do not return your product to the store!
    After referring to the User's guide, if you still need
    assistance, call Brother Customer Service at:
    Voice: 1-877-BROTHER
    Web: www.brother-usa.com
    Fax: 1-901-379-1210
    If you need to locate a service center, please call
    1-877-BROTHER or visit us at www.brother-usa.com
    Declaration of Conformity
    (Europe/Turkey only)
    We, BROTHER INDUSTRIES, LTD
    15-1, Naeshiro-cho, Mizuho-ku,
    Nagoya, 467-8561, Japan
    declare that this product is in compliance with the essential
    requirements and other relevant provisions of Directives
    2004/108/EC and 2009/125/EC.
    The Adapter AD-24ES is in compliance with the essential
    requirements and other relevant provisions of Directive
    2006/95/EC.
    The Declaration of Conformity (DoC) is on our Web site.
    Please go to http://solutions.brother.com -> choose region
    (eg. Europe) -> choose country -> choose your model ->
    choose “Manuals”-> choose Declaration of Conformity
    (*Select Language when required).
    *
    1
    Visit us at http://solutions.brother.com/ for the latest
    information about the recommended batteries.
    Specifications
    Dimensions:
    (W x D x H)
    Approx. 6.49" × 6.10" × 2.67"
    (Approx. 165(W) × 155(D) × 68(H)mm)
    Weight: Approx. 1.08 lb. (Approx. 490 g)
    (without batteries and tape cassette)
    Power supply: Six AAA alkaline batteries (LR03)
    Six AAA Ni-MH batteries (HR03)*
    1
    Optional AC adapter (AD-24ES)
    Tape cassette: Brother TZe tape (width)
    0.13" (3.5mm), 0.23" (6mm),
    0.35" (9mm), 0.47" (12mm)

Do you have a question about the Brother PT-D200?

Ask the question you have about the Brother PT-D200 here simply to other product owners. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Brother PT-D200 owners to provide you with a good answer.

View here the free Brother PT-D200 manual. Have you read the manual but does it answer your question? Then ask your question on this page to other Brother PT-D200 owners.

Product specifications

Brand Brother
Model PT-D200
Product Label Printer
EAN 12502631897, 12502633365, 1910027705, 4977766711678, 4977766713092, 4977766713115, 4977766713153, 4977766713252, 660814217867
Language English
Filetype PDF
Printing
Print technology Thermal transfer
Colour -
Maximum resolution 180 x 180
Print speed 20
Vertical printing
Maximum print height 9mm
Maximum printing width 12mm
Design
Display LCD
Display number of lines 1
Display number of characters 15
Product colour Grey, White
Other features
Print preview
Memory capacity 2400
Number of label formats 4
Label type 3.5mm, 6mm, 9mm, 12mm
Number of frames 97
Ports & interfaces
Ethernet LAN
Wi-Fi
Paper handling
Maximum label length 300
Performance
Tape type TZe
Number of styles 9
Underline
Number of fonts 14
Tape cutting Manual
Number of printing lines (max) 2
Power
Number of batteries supported 6
Battery type AAA
Energy Star certified -
Auto power off
Weight & dimensions
Width 165mm
Depth 155mm
Height 68mm
Weight 490

Buy related products:

    Related products

    Label Printer Brother